[WIP] FGM-148 Javelin

[ANW1173]

I started working on this yesterday, there's not much I want to say. but i need your feedback

[ismaelassassin]

poly count?

[anantdeathhawk]

Please post the pictures with lines/mesh as well.

[ANW1173]

poly count?

34k for now. Later I will bake it to a lower verts

[ANW1173]

Please post the pictures with lines/mesh as well.

remember this is the high poly version, I haven't made the low poly yet

[Hokunin]

Finally, someone is making a Javelin. Good job.

[anantdeathhawk]

Looks good, if it is this is high poly, Looks okay to me. But the fire control unit doesn't has the foam around it.
Plastic toy version


I hope texture makes it look like this.

[ANW1173]

Looks good, if it is this is high poly, Looks okay to me. But the fire control unit doesn't has the foam around it.
Plastic toy version


I hope texture makes it look like this.

yes that is my reference for textures. thanks for the suggestion

[camo]

Rear end cap is looking a little large but otherwise nice work!

Also what version of the javelin were you aiming for?

[ANW1173]

Rear end cap is looking a little large but otherwise nice work!

Also what version of the javelin were you aiming for?

I don't know maybe the new version. I think the only difference is in the tube

[ANW1173]

I'm not very good at UV packing. what do you think about this?

[camo]

I don't know maybe the new version. I think the only difference is in the tube

It looks like you're making the early version which tbh is fine, gives us a little more flexibility for factions and theatres etc. Could you post the latest wip?

[ANW1173]

It looks like you're making the early version which tbh is fine, gives us a little more flexibility for factions and theatres etc. Could you post the latest wip?

this is my current proggres . I haven't finished the tube yet
5k verts

[ANW1173]

what do you think about this, still med poly

[Mineral]

I think the UV is fine, but might be a bit too tightly packed. Specially when the mipmap versions are generated you might get some slightly bad results.

[ANW1173]

I think the UV is fine, but might be a bit too tightly packed. Specially when the mipmap versions are generated you might get some slightly bad results.

indeed some are generated like objects that are a bit difficult but not all of them. I use the tool to pack everything so it's a bit messy but fully packed.
ok then i'll add space for the uv so it's not too tight
thanks for the suggestion.

[Mats391]

Can you post more pictures of styrofoam covers? In your first post the one on the rear does look too big.
Also the covers are not 100% round, but have a flat spot on top

Here they rest on that flat spot:
https://filecache.mediaroom.com/mr5mr_l ... 0Model.JPG

Here you can see it on rear one:
https://cdn.dvidshub.net/media/thumbs/p ... 0w_q75.jpg
https://nationalinterest.org/sites/defa ... ult_18.jpg
https://upload.wikimedia.org/wikipedia/ ... 21562).jpg

[ANW1173]

Can you post more pictures of styrofoam covers? In your first post the one on the rear does look too big.
Also the covers are not 100% round, but have a flat spot on top

Here they rest on that flat spot:
https://filecache.mediaroom.com/mr5mr_l ... 0Model.JPG

Here you can see it on rear one:
https://cdn.dvidshub.net/media/thumbs/p ... 0w_q75.jpg
https://nationalinterest.org/sites/defa ... ult_18.jpg
https://upload.wikimedia.org/wikipedia/ ... 21562).jpg

okay I'll justify now, I didn't notice there was anything like that on the foam/cover, thank you.

[ANW1173]

progress updates :
I have finished baking the model need advice.
8k tris

[Mats391]

Further references for the rear cap:
https://youtu.be/CfXf98FglTo?t=10
https://u0v052dm9wl3gxo0y3lx0u44wz-wpen ... nistan.jpg

It is closed until missile is fired. The missile ignition destroys the middle part. In 1p this wont matter as you never see the rear, but in 3p would be good to add the middle part.